Pro Level Functional training Macrocycle 2-B

Weeks 19-24 of Macrocycle 2 for Functional training. This is a Tuesaday workout(upper body). Do 5-10 minutes of a dynamic warm-up to start workout. Complete in supersets of 2-3 exercises with 45 seconds rest between exercises. Rest 1-2 minutes between circuits.

Plyometric Depth Pushups

1. Start by placing feet on a bench and your hands on steps or blocks of your desired height.
2. Begin by getting into a push up position with your hands on the blocks.
3. Proceed into a pushup and when you push to extend your arms you should push hard enough to allow your hands to leave the blocks and land on the floor.
4. Once your hands have landed on the floor proceed into another pushup. Press up off the floor with enough force to have your hands leave the floor and land back on the blocks.
5. Repeat this cycle for the desired number of repetitions.

Hang High Pull

Keep torso straight but bent forward at the hips slightly.
Explosively raise the bar by extending the hips, knee and ankle in a “jumping action”.
Keep your elbows out and shoulders directly above bar as long as possible.
Keep the bar close to the body.
Once you have extended the lower leg shrug your shoulders and at maximum elevation of the shoulders start pulling with the arms.
Keep the elbows high during the pull until the highest point.
This should be a fluid motion where all the steps flow together.

Use 80-90 of max here, for pull. Use a heavier weight than you would on cleans.

Hang Snatch

Keep torso straight but bent forward at the hips slightly.
Explosively raise the bar by extending the hips, knee and ankle in a “jumping action”.
Keep your elbows out and shoulders directly above bar as long as possible.
Keep the bar close to the body.
Once you have extended the lower leg shrug your shoulders and at maximum elevation of the shoulders rotate the arms up and around above your head by exploding forward with your hips.
Slightly flex the hips and knees to absorb the weight.
This should be a fluid motion where all the steps flow together.

Use a lighter weight than on a regular snatch, but still heavy enough to do no more than 1-2 reps.

Supine DB chest press on ball

1. Lie on your back on a stability ball with your hips parallel with your upper body.
2. Hold a dumbell in each hand with your arms extended.
3. Bend your elbows and lower the dumbells down towards your chest. Keep your elbows at about 90 degrees and your wrists directly above your elbows.
4. Return to the starting position and repeat.

Front Pulldown

1) Adjust seat or knee pad height so that knees are secured while seated.
2) Grasp bar with a overhand grip wider than shoulder width apart and sit with knees secured in pads.
3) Start position: Fully extend arms with elbows facing out with back straight (you may lean back at hips approximately 5°-10°).
4) Pull bar down to upper chest area and squeeze shoulder blades together at end of movement.
5) Return to start position.
6) Remember to keep torso stationary throughout movement.

See Saw Press

Stand with feet shoulder width apart and knees slightly bent.
Start position: Position DB’s or kettleballs to ear level with an overhand grip (palms facing forward).
Press one hand up above head keeping the wrist over the elbow and arms moving parallel to the body at all times.
Return to start position and repeat with other arm.
Remember to keep back and head straight in a neutral position - hyperextension or excessive flexion may cause injury.

Dip

1. Step up on foot platform (if available) and position hands on dip bars.
2. Start position: Remove feet from platforms and suspend the body with slightly bent elbows. Lean forward slightly so that your elbows are slightly past the plane of your back and knees slightly bent.
3. Lower your body until your upper arm is parallel to the floor.
4. Return to starting position by extending the elbows to a slightly bent position.
5. Remember to keep the trunk bent forward, head neutral, and chest up.

Use a weighted belt for added resistance.

Dumbbell Hammer Curl

1) Stand with feet shoulder width apart and knees slightly bent or sit in upright position.
2) Start position: Grasp DB’s with neutral grip (palms facing each other) and allow arms to hang down at sides. Elbows should be close to sides.
3) Flex at the elbows and curl DB’s up to approximately shoulder level. Keep elbows close to sides throughout movement. This exercise may be done one arm at a time.
4) Return to start position.

Seated Reverse Cable Curl

1) Grasp cable handle. Sit in upright position and rest forearms on corresponding thighs with the palms down or rest forearms on a flat bench or training table.
2) Hands and wrists should be off the thighs or table (as shown).
3) Raise the weight by extending at the wrist.
4) Lower the weight and repeat as prescribed.
5) Remember to keep the forearms flat and supported on the thighs or bench throughout the movement. Trunk should be flexed forward at the hips - keep back straight throughout movement.